The Team Associated RC10 B74 Team 1/10 4WD Off-Road Electric Buggy Kit was developed to deliver the performance you expect from an Associated wheeler, with the durability necessary to go toe to toe in the heat of battle. Features like easy-access, quick-change differential height make tuning for different track surfaces and ride heights easier than ever. 7075-T6 aluminum bulkheads and arm mounts provide precision and durability, while the updated shocks with increased stroke length allow for more consistent jumping and landing. Also included, a rear hub assembly with a modular vertical ball stud mount and axle height insert system to allow the finest roll center adjustments possible. These, along with many other innovative features, give the RC10B74 Team Kit the performance, durability and adjustability you need to make it to the top of the podium.
NOTE: Model shown complete for illustrative purposes only and is not included.
Features:
Chassis:
2mm hard-anodized 7075-T6 aluminum chassis provides improved flex characteristics and minimal mass
2.5mm graphite center bulkhead brace for improved stiffness and reduced mass
Steering:
Ball bearing raced 7075-T6 aluminum steering rack and composite steering bellcranks with 2.5mm graphite input arm offers optimized Ackermann and adjustable steering rate
Redesigned steering blocks with larger outer ball bearing and increased bearing spacing for improved durability
Diffs and Slipper:
Quick-change adjustable differential height with 7075-T6 aluminum bulkheads. Four independent front and rear diff heights possible.
Easy-access differentials for worry-free maintenance and adjustment
Fluid-filled gear differentials with machined ring gears, front and rear
Updated 3-pad slipper assembly allows use of center differential without changing center bone length
Suspension:
Optimized suspension arm geometry with improved durability and stiffness
Symmetric rear arms with improved geometry can be flipped to allow a "split" for rear shock mounting position
7075-T6 aluminum arm mounts with optimized roll center positions use inserts, which allow fine tuning for a large range of anti-squat, kick-up, and toe adjustments
Common front and rear anti-roll bars to minimize spare part count
Anti-roll bar sets for both carpet/turf and dirt included Shocks
4mm graphite shock towers front and rear for improved stiffness and durability
V2 12mm Big Bore threaded aluminum shock with X-rings for low friction assembly
Updated shock lengths front and rear with longer stroke allows increased droop and up-travel for more consistent jumping and landing
Machined shock pistons for more precise fit and smoother operation
V2 12mm shock springs for lower achievable ride height and nimbler feel
Other:
CVA assemblies for center drive-line with aligned shafts for minimal torque loss and improved efficiency
Redesigned rear hub assembly with modular vertical ball stud camber link mounts and axle height system for precise roll center adjustments
Outer rear hinge pins captured with bolt head and lock nut for increased durability
7075-T6 aluminum motor mount and 7075-T6 aluminum center bulkhead have increased rigidity to maintain more accurate gear mesh
2.5mm graphite battery strap with sliding support tabs for fine tuning battery position (accepts any R.O.A.R. approved 2S "shorty" packs)
7075-T6 aluminum 9° caster blocks
"Floating" servo mount with 7075-T6 aluminum mount and 2.5mm graphite brace
Factory Team ball bearing set with 26 precision ball bearings, now oiled instead of greased for more efficient drivetrain
Aluminum clamping wheel hexes, front and rear
Lightweight clear body and clear wing included
Specifications:
Scale: 1:10
Power: Electric
Length (with wing): 395mm (15.55”)
Width: varies
Weight (chassis only): 930g (2.05 lb)
Wheelbase: 280.5-285.5mm (11-11.24”)
Internal Gear Ratio: 2.50:1
Needed to Complete:
2-Channel Radio System
ESC
540 Motor
Pinion Gear
Steering Servo
1/10 Buggy Wheels, Tires, Inserts & CA Glue
Polycarbonate Paint
2S 7.4V LiPo Shorty Battery Pack
Compatible Battery Charger
Other helpful items needed: Silicone Shock Fluid, Silicone Diff Fluid, Body Scissors, thread-locking compound, Body Reamer, FT Hex/Nut Driver set, CA tire adhesive, Hobby Knife, Needle Nose Pliers, Wire Cutters, Soldering Iron, Calipers or Precision Ruler.
